英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Figuring wire length with a ohmmeter? | Information by Electrical . . .
    An ordinary ohmmeter won't do it From the ITT "Radio Engineers Handbook" the resistance of #3 Annealed copper wire at 20 C (68 F) is about 0 197 ohms per 1000n ft Thus, your resistance for 600 ft would be about 0 118 ohms To measure this you need a 4 terminal ohmmeter This you can make by connecting a known DC current of about 10 A thru the
  • Question about the difference between an ohm-meter and a megger
    A ohmeter, is designed to measure ohms actually it dosent measure ohms it calulates ohms based on an applied voltage and a measured current, (snip) Right, I understand that, if the megger reads 500 Meg, the ohmmeter should read an overload, but it didn't It read 50K or so that's the wierd part of it
  • Infinity readings | Information by Electrical Professionals for . . .
    Along with some less common methods, an ohmmeter can apply a fixed voltage, and measure the current The display must read the inverse of the current, making for an odd looking scale on an analog meter
  • Digital Multimeter for resistance | Information by Electrical . . .
    The ohmmeter reading are actual readings Take my 20K reading of 04 Larry says "For example, if you get a reading of 3 87 with the scale set to 20K, then the resistance is 3 87K ohms So that means my resistance would be 04 ohms, but my reading at the 200 ohm scale was 44 9 ohms No, it means 04 K ohms
  • Sketch a diagram showing the ohmmeter face for a reading of . . . - bartleby
    Solution for Sketch a diagram showing the ohmmeter face for a reading of 1 2 kΩ Indicate the setting of the multi-tester knob
  • Answered: RTD Interface Problem #2: The circuit below was . . . - bartleby
    RTD Interface Problem #2: The circuit below was briely discussed earlier in the course This is an RTD interface which means it is fundamentally an ohmmeter The block X1 develops a known current of 1mA which will then develop a voltage across the RTD (R5) The resistors R1-3 represent the resistance of the "lead" wires going out to the RTD which is typically located a long distance (100's to
  • While measuring resistance: Technician A uses an ohmmeter to . . . - bartleby
    While measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit Technician B uses a voltmeter to measure voltage drop
  • Figuring wire length with a ohmmeter? | Page 2 | Information by . . .
    Another low-tech way that is neater and requires less space is to get a second, empty spool and set both spools up side-by-side on cable pulling stands Have an assistant wind the wire off the filled spool and onto the empty spool, while you use a measuring wheel pressed against the wire on the spool to measure its length
  • Answered: A machine part has a resistor X protruding from an . . . - bartleby
    An ohmmeter connected across a and b reads 2 00 N Part A What is the resistance of X? Express your answer in ohms Figure 1 of 1 X = 2 73 Ω а Submit Previous Answers Request Answer 15 0 5 0 10 0 X Ω Ω X Incorrect; Try Again; 5 attempts remaining ww- A machine part has a resistor X protruding from an opening in the side
  • Chapter 32, Problem 2PA - bartleby
    Solution Summary: The author explains whether the motor winding is connected wye or delta using an ohmmeter Dual voltage motors can be operated on two voltage levels BUY Delmar's Standard Textbook Of Electricity 7th Edition ISBN: 9781337900348 Author: Stephen L Herman Publisher: Cengage Learning S Safety, Basic Electricity And Ohm's Law 1 Atomic Structure 2 Electrical Quantities And Ohm’s





中文字典-英文字典  2005-2009